![]() ![]() The barrel profile on my PTR Industries K3P did not allow for the use of the 5/8 x 24sized shims. Warming up the silencer (usually by shooting through it) will expand the mount enough to loosen it up. Over the course of two months, I used my new Saker/KYMO setup on a variety of hosts, all of which functioned perfectly.Ī quick note about most quick disconnect silencer mounts – trying to remove a silencer that has cooled on a mount can be difficult due to material expansion and contraction. Rotating Saker/KYMO combination against the muzzle device, you can feel the difference in lug/notch sizes, until the whole unit drops into place.Īlternatively, if you timed your flash hider or brake properly, the notch visible on the ring of the KYMO will index at the 12 o’clock position. The three internal lugs in the mount and the three notches on the muzzle device indexes into a single position. Weight: 4.5 oz – Omega Mount 4.6 oz – Saker Mountīesides being less intricate and more reliable, the KYMO mount differs from the Trifecta in that it only installs one way.If you are completely green to the basics of gunsmithing or are unsure at any point during the process, stop and contact a gunsmith or drop the guys at Dead Air a line for advice. There is no need for excessive force, just tighten until the two mating surfaces contact each other. #Dead air keymo muzzle devices installRepeat the process in reverse to install the KYMO mount. After removal, inspect and clean the Saker’s threads. Use the two wrenches that came with your Saker and align them so that squeezing them together rotates the original MAAD system counter clockwise. ![]() Installing the KYMO mount itself is also a simple task. The internal lugs of the KYMO mount that mate up with the muzzle device. Semi-permanent installations should get a high-heat thread locker such as Rocksett. Using a torque wrench is advised, but those with a few muzzle device installations under their belt will be able to tighten by feel. This will help with attaching the silencer without having to feel for the correct notch locations. Usually I don’t feel the need to time/index flash hiders, however the KYMO mount is notched so that if the brake or flash hider is installed correctly, the notch/mount point will be in the 12 o’clock position. Brakes should be “timed” – the ending rotation after torquing indexes the circular gas ports upwards. Once you spin off the muzzle device, clean the threads and inspect the barrel shoulder for any glaring issues.Įach muzzle device comes with a set of shims of different thicknesses. #Dead air keymo muzzle devices freeI recommend using a receiver block or better yet a reaction rod that fits into the locking lugs of an AR15 barrel extension to safely get enough torque to break your brake free (like that?). ![]() For most of us with barrels threaded to a standard 1/2 x 28 or 5/8 x 24 thread pitch, the original muzzle device is removed using an AR15 armorers wrench or the SilencerCo tool that came with your silencer by turning it counterclockwise. KYMO Installation:įirst, replacing the flash hider or muzzle brake. Lantac recommends the use of semi-permanent thread locker Rocksett, sold separately.The indexing notch on the KYMO mount ring will index at the 12 o’clock position if the muzzle device is properly timed. Users should follow shooting guidance for the Wolfman as supplied by Dead Air. The mount design is fully licensed from Dead Air, therefore customers suppressor warranty remains unaffected. Shooters can now enjoy advanced weapon control with the ability to mount the Dead Air Wolfman® KEYMO silencer to their firearms.ĭragon brakes are precision manufactured on Swiss lathes and machined from AISI4150 steel that is then hardened to 48-52Rc (Rockwell C) and QPQ (Quench Polish Quench) Nitrided to AMS2753D standards for enhanced corrosion resistance and improved lifespan. Its unique Short Energy Pulse system reduces length of recoil so that repeating shot energy cannot overlap and knock the shooter off target.įull auto fire is possible with massively reduced recoil and muzzle climb, meaning that all shots fall on target. Manufactured to the highest quality standards and featuring a patented design, the LANTAC DGN9MMC-WM™ Muzzle Brake offers improved recoil management and muzzle rise over competitors products. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |